www.blomberginternational.cominfo@blomberginternational.comDishwasherInstallation ManualDW 55502 FBIDW 55502 SSDW 25502 WDW 25502 BDW 24100 BDW 24100
7USA6.3.1 INSTALLING THE FOOT SUPPORTSSupplied (4)
8USAAdjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height.Adjust the rear foot level wi
9USA6.5 PREPARING THE WATER CONNECTION (A)Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder connections
10USA6.6 DRAIN PREPARATIONThe dishwasher drain hose may be connected to the drain plumbing in one of three ways (Figure A, B, C). Notice :• Either on
11USA6.7 STEAM PROTECTION FOILSteam will form inside the dishwasher during operation. At the end of the cycle, when the dishwasher door is opened, it
12USA7. PLACEMENT OF DISHWASHER INTO THE OPENINGNow place the dishwasher into the opening and get ready to connect all hoses and electrical connection
13USA7.1.2 WATER SUPPLY CONNECTIONWater supply may be connected to the dishwasher in one of two ways:• With metal braided hose.• With copper tubing.
14USA7.3 READJUSTING FOOT LEVELSNow that the dishwasher is in the cabinet you must readjust the feet to bring the dishw
15USALock the toe kick brackets as shown with the plastic tab in the figure C by pushing the plastic tab on the dishwasher into th
16USA 7.5 INSTALLING THE OUTER DOOR(DW 55100 FBI, DW 55502 FBI)Measure the height and width of
DishwasherInstallation ManualDW 55502 FBIDW 55502 SSDW 25502 WDW 25502 BDW 24100 BDW 24100 SSDW 24100 WDW 25502 BDW 25502 SSDW 25502 WDW 55100 FBIDW 5
17USA5. Attach the two mounting brackets to the wooden door with 4 screws (Ø 1/8” x 5/8” (Ø 3.5mm x 14mm) (Figure A).6. Mount the w
18USA7. Open the door and remove the two caps and two screws inside the door at position 1 and 3 (Figure C).8. Usi
19USA11. Check whether the bottom of the door hits the toe kick of the kitchen cabinet (A).11.1. If the door hits the toe kick cut the necessar
20USA Notice :If you have a European kitchen or want to install a wooden toe kick to match
21USA8. INSTALLER CHECKLISTYour installer must have completed and checked the following:• The dishwasher is square and level.• The dishwasher is fas
Contents1. IMPORTANT SAFETY INSTRUCTIONS 11.1 INSPECT THE DISHWASHER 21.2 HOW TO CONTACT US : 22. TOOLS WHICH MAY BE NEEDED 33. MATERIALS WHICH MA
1USAINTRODUCTIONPlease read this installation manual and particularly the safety instructions completely and carefully. They will
2USA• If the dishwasher is installed in a location that experiences freezing temperatures (e.g. in a vacation home, cabin, etc.), you must drain all
3USA2. TOOLS WHICH MAY BE NEEDED3. MATERIALS WHICH MAY BE NEEDED(Additional materials may be required to comply with local codes)Hot Water Supply Line
4USA4. MATERIALS SUPPLIED4.1 PARTS SUPPLIEDParts for your dishwash
5USA5. DISHWASHER SPECIFICATIONS
6USA6. ENCLOSURE PREPARATION6.1 ELECTRICAL PREPARATION WARNINGThe dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected to a
Comments to this Manuals