DishwasherInstallation ManualUSAFOR MODELSDW 14110 NBL00DW 14120 NBL00DW 14140 NBL00DW 15110 NBL00DW 15111 NBL00DW 15120 NBL00DW 15121 NBL00DW 15140 N
To the right side position the cable extending approximately5½" (140 mm) (Figure B).Remove 2 15/16" - 3 15/16" (75mm-100mm) of the cabl
Measure the height of the enclosure.If the height of the enclosure is 337/16" to 34¼" (850 mm- 870 mm) use short supports as shown in th
ÝNotice :=Make sure the dishwasher is plumb and notice dishwashercan be placed with a small clearance under the countertop.Adjust the front foot level
Remove the junction box cover by removing the screws asshown in the figure. They will be reinstalled later.WARNINGInstallation should be perfo
ÝNotice :=Either one of the above methods must be used or thedishwasher will not operate properly.= A hose that attaches to a sink spray can burst if
CAUTIONMake sure all hoses and electrical wire are pulled throughthe side opening of the cabinet, no hoses are kinkedand all slack is taken out as sho
CAUTION= Hot water supply line: Use minimum 3/8 O.D. coppertubing or metal braided dishwasher supply line.= Temperatures required for soldering and s
WARNING= Improper connection of the equipment-groundingconductor can result in a risk of electric shock.Check with a qualified electrician or se
ÝNotice :=For models, DW 34100 NBL00, DW35100 NBL00,DW 36100 NBL00, DW 36101 NBL00, note that youshould keep the total height of the dishwasher at321/
ÝNotice :ABprCn7.4 ADJUSTING THE MOVABLE TOE KICKNow that you have successfully installed the dishwasher,you need to attach the toe kick to the dish
??Figure A7.5INSTALLING THE OUTER DOOR(DW 34100, DW 35100, DW 36100, DW 36101)If the enclosure height is above 331/16 (840 mm) use nand o labelle
3. Lay the schematic over the door from the bottom up andmark holes on the wooden door as shown in the drawing(Figure A).4. Place the plastic mounti
6. Cut the small tabs on the mounting brackets off(Figure A).8. Mount the wooden door onto the dishwasher with theplastic mounting brackets whi
10. Using the four screws Ø 3/16"x 111/16" (Ø 4 mm x 43mm) provided, attach the wooden door to thedishwasher at position 1 and 3 (Figure A)
ADJUSTING DOOR TENSION WITH CUSTOMWOODEN DOOR(DW 34100, DW 35100, DW 36100, DW 36101)Check the door tension of the dishwasher: If the door closestoo q
ÝNotice :If you have a European kitchen or want to install a wooden toe kick to match your kitchen, please refer to oneof the two drawings given below
ÝNotice :ÝNotice :ÝNotice :ÝNotice :Your installer must have completed and checkedthe following:= The dishwasher is square and level.= The dishwasher
17 2568 01 00-USA
Installation ManualFor Dishwasher ModelsDW 34100 NBL00DW 34110 NBL00DW 34120 NBL00DW 34140 NBL00DW 36100 NBL00DW 36101 NBL00DW 36110 NBL00DW 36111 NBL
To prevent accidents, which could cause serious injury or death, as well as machine damage read these instructions before installation and / or use.Co
1. IMPORTANT SAFETY INSTRUCTIONSIn addition to these instructions, the dishwasher shallbe installed:= In accordance with all local codes or, in absenc
ÝNotice :After unpacking the dishwasher and prior toinstallation, thoroughly inspect the dishwasher forpossible freight or cosmetic damage. Repo
Hot Water Supply Line - Minimum 3/8" O.D. copper tubing or metal braided dishwashersupply line.Shut-off valve and fittings appropriate for hot wa
4. MATERIALS SUPPLIED4.1 PARTS SUPPLIEDParts for your dishwasher will come in several plastic bags.Check your parts bags shown to make sure you have
ÝNotice :=For proper dishwasher operation and appearance ensurethat the enclosure has the minimum dimensions shownin the figure above.WARNINGTo avoid
Comments to this Manuals